Index of /~publicaccess/cho/700125-9e00i_utiliboot-v5.0.1
========================================================================
Release: v5.0.1
Date: 2012-10-01
Details:
New Features:
eurotech_carrier_tc:
- Enable PPS support.
- Enable user mode SPI support.
Changes:
bsp layer:
- Updated eurotech_api_examples to 700050-4C01d.
- Updated the eurotech_api_modules package using 700050-4603d.
- Build EMGD as module to support suspend and hibernate.
- Update smsc75xx USB LAN driver to version 1.1.0.
========================================================================
Release: v5.0.0
Date: 2012-08-20
Details:
New Features:
- Updated layers for WRL 4.3 for all products.
- eurotech_carrier_tc is a supported BSP for WRL 4.3.
Changes:
bsp layer:
- Updated layers for WRL 4.3. Kernel version is now
2.6.34.10. EG20T PCH patches were pulled from the new
intel_atom_eg20t_pch and kbc_km2m806 BSPs.
- Update iw package to iw-3.6.
- Reopen touchscreen when resuming from a suspend.
- Add eth_epr_extras and eth_name_bsp to feature/eurotech_versions.
- Add feature/smsc-lan7500 for the SMSC LAN75xx NIC family.
- Blacklist wifi modules that conflict with feature/wifi-iwlagn.
- Refactor eurotech_helios gps support into feature/gps.
eurotech_carrier_tc:
- Add hibernation and power state details to README.
- Support bootloader on EG20T UART (rev B module only).
- Make base_baud for EG20T UART's dependent upon CPU stepping.
- Relax ACPI resource restrictions so DME1737 loads.
- Switch to stock EG20T PCH I2C driver, i2c-eg20t.
- Fix reporting of MAC when initializing pch_gbe.
eurotech_vector:
- Added optional feature/gateway for ReliaGATE.
eurotech_helios:
- Switch to including new feature/gps.
========================================================================
Release: v4.5.0
Date: 2012-04-30
Details:
New Features:
bsp layer:
- eurotech_aludra is a supported BSP for WRL 4.2.
- feature/power_management:
* Enable hibernate (S4) power state.
* Add usb unbind/bind PM processing to allow EHCI recovery
after thaw.
- Add resume_delay kernel parameter for slow media and contollers.
Changes:
bsp layer:
- Split the board-specific feature/eurotech_versions_firmware
out of the general feature/eurotech_versions template to
support non-catalyst boards.
========================================================================
Release: v4.4.2
Date: 2012-04-16
Details:
New Features:
- None.
Changes:
bsp layer:
- Update the eurotech_api_modules package using 700050-4603c.
- Add support for relative filename paths to install-layers.sh.
========================================================================
Release: v4.4.1
Date: 2012-04-11
Details:
New Features:
- None.
Changes:
- Update eurotech_api_modules and eurotech_api_examples.
- Add install-layers.sh to source release to help with manual
layer installation.
========================================================================
Release: v4.4.0
Date: 2012-02-29
Details:
New Features:
- eurotech_proteus is a supported BSP for WRL 4.2.
- feature/power_management supports suspend (S3) power state
for all BSPs.
Changes:
bsp layer:
- Add feature/eurotech_smapi to all Catalyst BSPs.
- Add driver for the DS28CM00 Silicon Serial Number device.
- Enable DS28CM00 driver for eurotech_duracor,
eurotech_dynavis and eurotech_isis.
- Add patch from Wind River to fix frozen X windows
on repeated suspend/resume operations when using the
Intel EMGD drivers.
- Refactor feature/power_management ACPI S3 kernel options
to be board specific.
eurotech_dynavis:
- Change default serial console to ttyS2, the service
panel serial port.
- Support cloned VGA display under xorg.conf.d by default.
eurotech_tc branch:
- Set option to treat MMC as non-removable to support
suspend/resume when running from the e.MMC device.
cfgbase layer:
- Refactor feature/power_management pm-utils video-quirks
to be board specific.
========================================================================
Release: v4.3.0
Date: 2011-12-20
Details:
New Features:
- eurotech_dynavis is a supported BSP for WRL 4.2.
bsp layer:
- Add compat-wireless package.
- Add feature/wifi-iwlagn to support Intel WiFi adapters.
- Add package for Intel Centrino Advanced-N 6205 firmware.
- Add iw package.
Changes:
bsp layer:
eurotech_duracor:
- Enable feature/wifi-iwlagn.
- Remove panel_pc templates.
cfgbase layer:
- Add iw to layer default packages.
eurotech_isis:
- Enable feature/wifi-iwlagn for ISIS devkits.
eurotech_duracor:
- Remove panel_pc templates.
recovery layer:
- Dynamically determine the default target and adjust grub
accordingly.
Defects:
- The feature/wifi-iwlagn and feature/wifi-atheros features
are incompatible. If both are included, you must use
blacklisting to prevent one set of modules from being
loaded. The example below disables the Atheros drivers
by appending the blacklist directives to the ath.conf file
for modprobe:
cat <<EOF >>/etc/modprobe.d/ath.conf
blacklist ath5k
blacklist ath9k
blacklist ath
EOF
========================================================================
Release: v4.2.1
Date: 2011-10-28
Details:
New Features:
- None.
Changes:
eurotech_duracor:
- Fixed linking of base feature/int-1410 to board specific
details for the DuraCOR 1400 configuration.
========================================================================
Release: v4.2.0
Date: 2011-10-17
Details:
New Features:
- Ported eurotech_duracor, eurotech_ec, and eurotech_isis
BSPs forward to WRL 4.2.
- eurotech_duracor supports the DuraCOR 1400 and DuraCOR Panel
PC variants.
Changes:
bsp and cfgbase layers:
- Moved socketcan, modem-sierra, wifi, wifi-atheros feature
templates from cfgbase to bsp layer.
- Moved dmidecode package from cfgbase to bsp layer.
bsp layer:
- Share touchscreen automatic calibration code with xinitrc.
- Split feature/socketcan-sja1000 out of feature/socketcan.
- Drop grub MMC patch in favor of toolchain patch from Wind River.
- Add support for Eurotech INT-1410 PC/104-Plus Audio Matrix module.
- Add support for Eurotech COM-1274 PC/104 communications module.
eurotech_vector:
- Fix defect where CAN bus interrupts were swapped.
eurotech_xl branch:
- Add missing kernel config option to enable I2C support.
wrs_meta branch:
eurotech_vector:
- Move CAN enablement to bsp template.
eurotech_isis (inherited by eurotech_duracor):
- Fixed SuperIO hardware monitoring support.
eurotech_duracor:
- Move wifi-atheros and modem-serial enablement to
bsp template.
========================================================================
Release: v4.1.0
Date: 2011-08-26
Details:
New Features:
- Ported eurotech_carrier_xl, eurotech_helios and eurotech_vector
BSPs forward to WRL 4.2.
- Add eurotech_versions utility for accessing system version info.
Additional scripts, eth_partno_* and eth_vers_*, provide
version strings for specific features.
Changes:
bsp layer:
- Touchscreen support was re-implemented using evdev.
- All serial consoles default to 115200 BAUD.
- X11 configuration was broken into a set of config fragments.
- X11 clones output on both SDVO and LVDS display ports.
- Famebuffer console support is no longer used.
- Utiliboot images support serial consoles on systems using
UART serial ports. i.e. not USB serial converters for the
console port.
========================================================================
Release: v4.0.0
Date: 2011-07-29
Details:
New Features:
- Ported layers to Wind River Linux 4.2.
Changes:
- Switched back to USB images from ISO hybrids.
- Renamed Utiliboot image to utiliboot.img.
cfgbase layer:
- Switched touchscreen support back to tslib instead of evtouch.
- Dropped add-on layer in favor of using the stock WRL 4.2
Xorg and Intel EMGD packages.
- Dropped qt and qt demos.
- Systems get their IP asynchronously after booting using
DHCP, as soon as the ethernet is attached.
- Removed boa and pyca packages because of conflicts with ESF.
- Added eurotech_api_modules package and added to
eurotech_carrier_tc.
esfbase layer:
- Removed the esfbase layer, because without boa there is
nothing to do.
bsp layer:
- Switched from vendor supplied to stock kernel drivers for
SMSC LAN9500 NICs. This affects all BSPs, but is most
significant for eurotech_tomra.
- eurotech_carrier_tc:
- Added support for the EG20T serial ports.
- Replaced the PCH I2C driver with the IOH I2C driver.
- Fixed soft reboot.
eurotech_isis:
- Re-added Ethernet support lost in the porting to WRL 4.1.
========================================================================
Release: v3.1.0
Date: 2011-06-03
Details:
New Features:
- All z5xx based boards have been ported forward to Wind River
Linux 4.1. The eurotech_helios BSP running on a Catalyst TRM
(Tomra) system is the only configuration tested for this release.
Changes:
cfgbase layer:
- Updated to Xorg 1.6 with EMGD drivers and QT demos.
- Switched touchscreen support to use evtouch instead of tslib.
- Added pm-utils to feature/power_management.
- Added i2c-tools.
- Enabled smsc9500 support on all hardware.
- Re-enabled the atheros, realtek and zydas wifi adapters.
- Disabled hardware cryptography for the atheros wifi devices.
- Switched socketcan support to stock kernel version.
bsp layer:
The kernel git repository was reorganized, and BSP
configuration options and patches moved into processor
specific branches with common patches placed into the
eurotech_base branch. The eurotech_xl, eurotech_tc, and
eurotech_lp branches are used as the basis for the BSPs
for boards using the z5xx, e6xx and n4xx/d5xx processors
respectively.
N.B. The catalyst_lp branch is incomplete, and there are no
supported boards in this release.
eurotech_xl, eurotech_tc and eurotech_lp branches:
- Tuned for the ATOM CPU.
- Added USB serial support.
eurotech_xl branch:
- Added Poulsbo/US15W LPC support.
- Added Poulsbo/US15W I2C support.
- Added Poulsbo/US15W GPIO support.
eurotech_tc branch:
- Added Topcliff/EG20T SPI support.
- Added Topcliff/EG20T I2C support.
- Added Topcliff/EG20T GPIO support.
- Added Topcliff/EG20T CAN support.
eurotech_carrier:
- Renamed to eurotech_catalyst_xl for consistency.
- Added SuperIO hardware monitor support.
eurotech_vector:
- Added CAN support.
========================================================================
Release: v3.0.0
Date: 2011-03-31
Details:
New Features:
- eurotech_carrier_tc, Catalyst TC Module Dev Kit, is a supported
BSP for WRL 4.1.
- Added the dmidecode, i2c-tools and pm-utils packages.
- Added dmidecode to the default Eurotech Product Run-time (EPR).
Changes:
- Renamed Utiliboot image to utiliboot.iso.
- Merged the wifi-ap layer into the cfgbase layer.
- Ported the BSP layers for existing Z5xx BSPs from WRL 3.0.2 to
WRL 4.1. The kernel git repository portion of the older BSPs
is not included, so these layers are incomplete and unsupported
in this release.
========================================================================
Release: v2.1.8
Date: 2011-03-17
Details:
New Features:
bsp layer:
- Added touchscreen support. This feature also enables VESA
framebuffer support.
- Added support for Eurotech TSC1 touchscreens.
- Added drivers and utilities to support the SMSC Lan9500
Ethernet NIC.
- Added power management support. This includes both options
for suspending the system to RAM as well for altering the
CPU frequencies.
eurotech_duracor:
- Added Guardian hardware monitor.
- Enabled USB OHCI to support the COM-1480.
- Added GPS support on the "Unita CBRCS"/SYS-0242 variant.
Changes:
bsp layer:
- Significantly reworked how the built-in command line
kernel support is implemented to support composition from
multiple configuration fragments.
- Replaced mchp-ts-inputattach package with the non-vendor
specific inputattach package.
- Enhanced GRUB to support for SD/MMC devices.
========================================================================
Release: v2.1.7
Date: 2011-02-01
Details:
New Features:
- Vector is a supported BSP for Wind River Linux 3.0.2.
Changes:
bsp layer:
- Updated EXAR USB UART driver.
- Added support for suspend/resume to EXAR USB UART driver.
- Added support for Microchip based touchscreens.
eurotech_duracor:
- Enabled stock WLAN and WWAN devices.
eurotech_helios:
- Required kernel parameters are now set via kernel config.
cfgbase layer:
- Dropped udhcpd and old C++ libraries.
- Added update-usbids script and updated USB and PCI ID DBs.
- Set ntpddate to sync hardware clock after successful update.
wifi-ap layer:
- Updated hostapd to 0.7.3.
- Reworked example scripts to ease testing.
recovery layer:
- Refactored from derived BSP templates into a feature template.
- Added support for SD/MMC devices.
========================================================================
Release: v2.1.6
Date: 2010-11-15
Details:
New Features:
- DuraCOR is a supported BSP for Wind River Linux 3.0.2.
Changes:
- Replaced rootdelay kernel argument with rootwait.
- Enabled I2C/SMBUS support.
- PATA slave devices are fully supported through the SCH driver.
- eurotech_isis:
* Enabled SuperIO hardware monitoring support.
- eurotech_helios:
* SSD is fully supported for Rev. A and later boards.
* Mandatory kernel arguments moved into the kernel config.
========================================================================
Release: v2.1.5
Date: 2010-10-26
Details:
New Features:
- None.
Changes:
- Fixed CONFIG_PCI_MSI such that kgdboe works on the Catalyst EC.
========================================================================
Release: v2.1.4
Date: 2010-10-04
Details:
New Features:
- None.
Changes:
- Changed the default device for reset_media to /dev/sdb for
catalyst_carrier and catalyst_ec.
========================================================================
Release: v2.1.3
Date: 2010-08-24
Details:
New Features:
- Catalyst EC Dev Kit is a supported BSP for Wind River Linux 3.0.2.
Changes:
- Modified xorg init scripts to keep default xterm within the display.
========================================================================
Release: v2.1.2
Date: 2010-08-06
Details:
New Features:
- Catalyst Module (Carrier) Dev Kit is a supported BSP for
Wind River Linux 3.0.2.
Changes:
- Utiliboot images are now always called utiliiboot-usb.img.
- Updated USB and PCI device ID databases.
========================================================================
Release: v2.1.1
Date: 2010-07-26
Details:
New Features:
- ISIS is a supported BSP for Wind River Linux 3.0.2.
Changes:
- Several issues relating to using a serial console were fixed.
========================================================================
Release: v2.1.0
Date: 2010-07-16
Details:
New Features:
- Added support for Vector.
- Added optional socketcan feature.
Changes:
- None.
========================================================================
Release: v2.0.3
Date: 2010-07-15
Details:
New Features:
- Added support for SATA drives on the Helios/Catalyst FX.
- Added experimental support for the on board NAND SSD on the
Helios/Catalyst FX.
- Fixed linux-live to support passing additional kernel arguments
via syslinux when booting from USB.
- Enabled the grub menu on ttyS0 for eurotech_carrier.
- Fixed a few problems with USB images produced using linux-live.
Changes:
- None.
========================================================================
Release: v2.0.2
Date: 2010-06-17
Details:
New Features:
- WiFi AP support has been added as an optional layer for Ralink
rt73 USB adapters.
Changes:
- Non-Ralink wifi adapters are not built in by default.
========================================================================
Release: v2.0.1
Date: 2010-05-28
Details:
New Features:
- BSP has been validated by Wind River for the Helios/Catalyst FX.
Changes:
- Updated for Wind River Linux 3.0.2.
- BSP has also been refactored into multiple layers to separate
pure BSP support from ESF support.
- busybox configuration for ESF provides a large set of default
utilities in addition to udhcpd.
========================================================================
Release: v1.4.0
Date: 2010-02-11
Details:
New Features:
- Added support for the DuraCOR, a product based on the Isis.
Changes:
- Added support for OHCI (USB 1.1) devices on all boards.
- Added ISA bus support for PC/104 systems.
- Added hand-built socketcan modules to the release.
- Changed the root password.
- Reconfigured to discard mail to root.
- Set the serial console device correctly for the Isis DevKit.
========================================================================
Release: v1.3.0
Date: 2010-01-07
Details:
New Features:
- Added support for the Catalyst Carrier DevKit.
Changes:
- Cleaned up board/eurotech_catalyst menu.lst:
* Default to hda.
* Default to serial for grub.
========================================================================
Release: v1.2.0
Date: 2009-12-08
Details:
New Features:
- Added support for the Isis DevKit, a Catalyst-based system.
Changes:
- Cleaned up documentation with other BSP targets.
========================================================================
Release: v1.1.0
Date: 2009-11-23
Details:
New Features:
- Added support for the Catalyst EC.
- Grub menu is available on both serial and video/keyboard.
- Both network interfaces are configured automatically.
Changes:
- Reworked the order that changes are being applied when
configuring the BSP by rearranging the source to not use
--enable-profile. Instead the configuration "target" is the
first template given to --with-template.
- The template for changing the type of root device accomplishes
the change using a script instead of overwriting files.
- Xorg/X11 support is part of the target template, and not a
CLI argument.
- The "unsupported" layer is now implied to the BSP layer,
and not a CLI argument.
- Start up of ntpd has moved into a patch of the feature.
========================================================================
Release: v1.0.0
Date: 2009-10-23
Details:
New Features:
- Added EXAR USB UART driver.
- Added X11 support using Debian binaries.
- Added GPS initialization.
- Added current USB and PCI device ID databases.
- Fixed soft rebooting.
- Back /tmp and /var/log using memory file systems.
Changes:
- Moved console from serial port to video w/keyboard.
- Turned off boa webserver by default.
- Completely replaced WRL grub with Debian grub.
- Switched to Wind River Linux 3.0.1 for the development environment.
![[ICO]](/icons/blank.gif){kind=icon}
![[PARENTDIR]](/icons/back.gif){kind=icon}
![[TXT]](/icons/text.gif){kind=icon}
![[ ]](/icons/unknown.gif){kind=icon}